Factory knockouts preserve galvanized coating and enclosure integrity. Field punching risks corrosion and rating loss. Spec guidance for Saudi MEP teams.
What Is the Difference Between Factory Knockouts and Field-Punched Openings on Galvanized Steel Electrical Boxes?
Factory knockouts are pre-formed, partially sheared openings stamped into the box wall during manufacturing. They are sized to standard conduit trade sizes and remain attached until the installer removes them with a controlled twist or light strike. Field-punched openings are cut on site using a hole saw, step drill, chassis punch, or knockout punch set. The critical difference is not the hole itself but what happens to the galvanized coating and the enclosure's structural and rating integrity around that hole. Factory knockouts preserve the zinc coating because the shear line is created before the box is formed and the coating is applied or because the stamping process is designed to keep the coating continuous at the knockout perimeter. Field punching cuts through the zinc layer, exposing bare steel to the atmosphere. In the Eastern Province's coastal humidity, that exposed edge becomes a corrosion initiation site within months. For MEP consultants naming boxes in a specification and contractors receiving them on site, the choice between relying on factory knockouts and resorting to field punching is a durability and compliance decision, not merely a convenience one.
How Many Knockouts and What Trade Sizes Should a Galvanized Steel Electrical Box Have for Saudi Projects?
The number and size of knockouts should match the conduit entry schedule for the box's location, with spare capacity for future modifications. Alrouf switch boxes (BB6 and BB7) are marked AL-ROUF KSA BS4662 and provide bottom knockouts of 1/2" (3) and 3/4" (1), plus side knockouts of 1/2" (4) and 3/4" (6). That configuration supports typical lighting and power switch points where a small number of 1/2-inch and 3/4-inch conduits enter from the bottom or side. For junction boxes, the knockout count increases with box size. The BB8 junction box (10×10×5.5 cm) has bottom knockouts of 1/2"-3/4" (6) and 3/4"-1" (2), with side knockouts of 1/2"-3/4" (4) and 3/4"-1" (4). The BB9 junction box (available in 15×15×5.5 cm and 15×15×10 cm) has bottom knockouts of 1/2"-3/4" (2) and 3/4"-1" (1), with side knockouts of 1/2"-3/4" (8) and 3/4"-1" (4). These are concentric or eccentric configurations depending on the model, allowing the installer to select the trade size that matches the conduit without cutting new holes. Review the full range of junction box sizes to match knockout patterns to your conduit schedule.
Why Does Field Punching Damage Galvanized Coating and What Does That Mean for Eastern Province Humidity?
Field punching removes the zinc coating at the cut edge, exposing bare steel to moisture and chlorides. In the Eastern Province, relative humidity routinely exceeds 60 percent, and coastal areas of Dammam, Khobar, and Jubail carry airborne chloride from the Arabian Gulf. Bare steel in that environment begins to corrode quickly, and the corrosion front can migrate under the adjacent zinc coating. The result is a rust ring around the field-punched opening, which is both a durability problem and an inspection finding. Factory knockouts avoid this because the opening is formed during stamping, and the coating around the knockout is continuous. When the knockout is removed, the break is clean and the exposed edge is minimal. The difference in coating integrity between a factory knockout and a field-punched hole is visible on close inspection and matters over the service life of the installation. For projects in coastal zones, see this guide to outdoor and coastal junction box corrosion protection.
Concentric vs Eccentric Knockouts: Which Should Be Specified?
Concentric knockouts are best where the conduit entry position is fixed and the installer needs to select a trade size without moving the centerline. Eccentric knockouts are best where the installer needs to remove a larger ring while keeping the opening close to the box edge or to an adjacent knockout. In practice, many Alrouf boxes use a combination: the BB8 junction box has bottom knockouts of 1/2"-3/4" (6) and 3/4"-1" (2), and side knockouts of 1/2"-3/4" (4) and 3/4"-1" (4). The 1/2"-3/4" knockouts are typically concentric, allowing either size at the same center. The 3/4"-1" knockouts may be eccentric to allow the larger size without shifting the opening. The specification should state which configuration is required where the conduit routing is tight, because the wrong choice can force a field modification.
What Workmanship Standards Should Contractors Follow When Using Factory Knockouts?
Factory knockouts should be removed with the correct tool and technique: a knockout punch or a controlled twist with pliers, not a hammer and chisel. The knockout should be removed completely for the trade size being used, and the resulting edge should be inspected for burrs. If a burr is present, it should be removed with a deburring tool or file before the conduit is connected. The connector should be seated firmly against the box wall, with the locknut tightened to the manufacturer's recommendation. The box should be inspected after knockout removal to confirm that the coating around the opening is intact and that the box wall has not been deformed. Any deformation should be corrected before the box is installed, because a distorted box can affect cover fit and device alignment. For proper connector seating, follow this guide on connecting EMT conduit to junction boxes.
How Should MEP Consultants Specify Knockouts to Avoid Field Modifications?
The specification should name the box model and the knockout configuration explicitly, and it should require the contractor to verify the conduit schedule against the knockout pattern before ordering. A generic specification that describes a "galvanized steel junction box" without naming the model leaves the knockout pattern to the supplier's discretion and increases the risk of a mismatch on site. Naming the model, such as BB8-001 or BB9-002, tells the contractor exactly what entry points are available and allows the supplier to confirm availability. The specification should also state the conduit trade sizes expected at each box location, so that the knockout pattern can be checked against the schedule. Where the schedule includes a size that is not covered by the standard knockout pattern, the specification should identify an alternative box model from the range rather than allowing field punching as a default.
What Is the Bottom Line for Saudi MEP Contractors on Knockouts vs Field Punching?
The bottom line is that factory knockouts should be the default and field punching should be the exception. Factory knockouts preserve the galvanized coating, maintain the box's structural and rating integrity, and reduce the risk of corrosion in the Eastern Province's humid and chloride-bearing environment. Field punching exposes bare steel, introduces burrs that can damage insulation, and creates an opening that was not part of the tested configuration. The cost of specifying the right box model with the right knockout pattern is small compared with the cost of remediating corrosion or addressing an inspection finding. For MEP consultants, the specification should name the model and the knockout configuration, require verification against the conduit schedule, and treat field punching as a deviation. For contractors, the workmanship standard should require correct knockout removal, deburring, and coating repair where field punching is approved.
◈ Key Takeaways
- ✦Specify the box model and knockout configuration explicitly so the contractor receives a box that matches the conduit schedule without field modification.
- ✦Treat field punching as a deviation: require deburring, zinc-rich coating repair, and recording on the as-built drawing.
- ✦Match knockout trade sizes to the conduit schedule; use concentric or eccentric patterns as appropriate for the routing.
- ✦In Eastern Province coastal projects, minimize field-punched openings to protect the G90 galvanized coating from humidity and chloride exposure.
- ✦Inspect boxes on delivery for knockout integrity and store them dry to prevent pre-installation damage.
Frequently Asked Questions
❓ What is the difference between knockouts and field punching on galvanized steel electrical boxes?
Knockouts are pre-cut, partially stamped openings in a galvanized steel electrical box that can be removed with a hammer or screwdriver, while field punching involves cutting or drilling holes on-site using tools like hole saws or punches. Knockouts save time and ensure clean, consistent openings, whereas field punching may be needed for custom configurations but can compromise the box's galvanized coating and structural integrity.
❓ Why should I use galvanized steel electrical boxes with knockouts in Saudi Arabia?
Galvanized steel electrical box knockouts in Saudi Arabia offer corrosion resistance and durability, essential for the region's harsh climate and construction standards. Pre-made knockouts simplify installation, reduce labor time, and maintain the protective zinc coating, unlike field punching which can expose bare steel to rust.
❓ Which knockout sizes are available on Alrouf galvanized steel electrical boxes?
Alrouf switch boxes feature bottom knockouts of 1/2" (3) and 3/4" (1), and side knockouts of 1/2" (4) and 3/4" (6). Junction boxes have varying configurations: BB8 has bottom knockouts 1/2"-3/4" (6) and 3/4"-1" (2), and side knockouts 1/2"-3/4" (4) and 3/4"-1" (4); BB9 has bottom knockouts 1/2"-3/4" (2) and 3/4"-1" (1), and side knockouts 1/2"-3/4" (8) and 3/4"-1" (4).
❓ Can I punch additional holes in a galvanized steel electrical box without damaging it?
Yes, you can field punch additional holes, but it requires proper tools like hole saws or knockout punches to avoid deformation. However, punching may remove the galvanized coating around the hole, exposing the steel to corrosion; it's advisable to use pre-knockout boxes where possible and apply a protective coating if field modifications are necessary.
❓ How long does it take to remove knockouts compared to field punching?
Removing knockouts is typically much faster, taking seconds per opening with a hammer or screwdriver, while field punching can take several minutes per hole and requires specialized tools. In time-sensitive projects in Saudi Arabia, using pre-knockout boxes can significantly speed up installation and reduce labor costs.
See the full Alrouf product range
Download the Alrouf 2023 catalogue and browse the product range.
Alrouf Electrical Accessories Manufacturer
Galvanized electrical boxes & precision metal-plastic components — Dammam








