A site-level guide to fixing galvanized steel electrical boxes in blockwork, precast and steel-frame construction across Saudi projects.
How Do You Fix a Galvanized Steel Electrical Box to Blockwork, Precast or Steel Frame?
For galvanized steel electrical box installation Saudi Arabia sites, the fixing method depends on the substrate: in blockwork the box is set into the wall during block laying or chased in afterwards and bedded in mortar; in precast panels the box is cast in at the factory or fixed to the panel face with proprietary anchors; on steel frames the box is mounted on bracketry or directly to studs before the drywall or cladding closes. In every case the box must be set to the finished plaster line, kept level and plumb, and anchored so that conduit entry and cover fit are not disturbed.
The decision is made daily on site, usually by the electrical foreman coordinating with the block layer or the precast erector. Getting it right the first time controls alignment, plaster depth, pull-out strength and rework. A box set 10 mm too deep will need a plaster ring or a longer screw; a box set too proud will stand out of the wall and crack the plaster around it. Neither is acceptable on a project with a snag list.
Alrouf manufactures its boxes in Dammam 2nd Industrial City from G90 galvanized steel as per ASTM-A653, with a 2-hour fire rating and country of origin Kingdom of Saudi Arabia. Switch boxes BB6 and BB7 are marked AL-ROUF KSA BS4662; junction boxes BB8, BB9 and BB10 are marked AL-ROUF KSA without BS4662. Those markings matter at handover, but they only survive if the box is fixed correctly in the first place.
The three substrates behave differently. Blockwork is forgiving but slow; precast is fast but unforgiving of dimensional error; steel frame is precise but demands coordination with the drywall or cladding package. The sections below take each in turn, then cover the interface details that apply to all three.
What Is the Correct Fixing Method for Galvanized Boxes in Blockwork Walls?
In blockwork, the correct method is to set the box during block laying wherever possible, bedding it in mortar to the plaster line and checking level with a spirit level before the mortar sets. Where the wall is already built, the box is chased in: cut a pocket slightly larger than the box, wet the pocket, bed the box in mortar or a suitable repair mix, and brace it until set. The box must be set so its front face finishes flush with the finished plaster, not the block face.
Plaster depth is the single most common source of rework. On a typical Eastern Province project the plaster may be 15 mm, but it can vary between internal and external walls and between specification sections. The foreman should confirm the plaster build-up with the finishing subcontractor before the first box is set, then use a setting gauge or a straight edge across the wall face to hold that depth consistently. A box set to the block face will end up buried; a box set to the plaster face will end up proud.
Conduit entry must be planned before the box is bedded. Alrouf switch boxes have bottom knockouts of 1/2" (3) and 3/4" (1), and side knockouts of 1/2" (4) and 3/4" (6). Choose the entry that matches the conduit route so the conduit does not have to be bent sharply behind the box, which strains the knockout and can crack the galvanized coating. Remove only the knockouts you need; the rest stay closed to keep mortar and plaster out.
Bracing matters. Mortar does not hold a box against gravity while it sets, so use a temporary brace, a batten screwed across the wall, or a purpose-made box support. Check level and plumb again after the mortar has taken its initial set, because bedding can shift a box slightly. On long runs of switch boxes, set a string line or laser at the finished plaster line and work to it; this is faster than checking each box individually and gives a consistent line that the plasterer can work to.
How Should Boxes Be Cast Into or Fixed to Precast Panels?
In precast, the box should be cast in at the factory wherever the design allows. The box is fixed to the mould or to the reinforcement cage in the correct position, with the conduit entry protected and the box face held to the finished panel face. Cast-in boxes give the best pull-out strength and the cleanest finish because there is no chase and no repair. The trade-off is that the position is fixed at the factory, so the setting-out must be right before the panel is cast.
Where the box is not cast in, it is fixed to the panel face after erection. The method depends on the panel: on a solid precast panel, use proprietary anchors rated for the substrate and the load, and set the box on a packing piece or a plaster ring to bring it to the finished line. Do not rely on mortar alone on a smooth precast face; it will not bond reliably. On a precast panel with a screed or drylining zone, treat the fixing as you would for blockwork, but confirm the panel thickness and the anchor embedment depth first.
Coordination with the precast erector is essential. The electrical contractor needs the panel layout and the cast-in positions before the panels are made, and needs to inspect the cast-in boxes on delivery. A box cast in the wrong position cannot be moved without cutting the panel, which is expensive and slow. A box cast in with its face proud or recessed will need a plaster ring or a chase, both of which add cost.
Alrouf junction boxes BB8, BB9 and BB10 are commonly used in precast for larger pull and jointing points. BB8-001 is 10×10×5.5 cm at 0.9 mm and 298 g, packed 50 pcs per pack; BB9-001 is 15×15×5.5 cm at 0.9 mm and 620 g, packed 20 pcs per pack; BB9-002 is 15×15×10 cm at 0.9 mm and 825 g, packed 12 pcs per pack; BB10-001 is 20×20×5.5 cm at 952 g. Their knockout patterns — BB8 with bottom 1/2"-3/4" (6) and 3/4"-1" (2), side 1/2"-3/4" (4) and 3/4"-1" (4); BB9 with bottom 1/2"-3/4" (2) and 3/4"-1" (1), side 1/2"-3/4" (8) and 3/4"-1" (4) — should be matched to the conduit route before the panel is cast. For a full comparison of enclosure formats, see this guide to pull box vs junction box selection.
What Changes When Fixing Boxes to Steel Frames and Drywall?
On steel frames, the box is fixed to the stud or to a purpose-made bracket, not to the drywall. The drywall is a finish, not a structure; a box fixed only to the board will move, crack the finish and fail at the first pull on a cable. Fix to the stud with a bracket or a box support that holds the box at the finished board line, and brace the stud if it is a light gauge that will deflect.
The finished line on a steel frame is the face of the drywall, not the face of the stud. The box must be set forward of the stud by the board thickness, plus any skim coat. Use a box support or a plaster ring to make that adjustment; do not pack the box out with timber or offcuts, which will shrink and move. On a fire-rated wall, the box and its fixing must not compromise the fire performance; the 2-hour fire rating of Alrouf boxes is a property of the box, but the wall assembly has its own rating that the fixing must respect.
Coordination with the drywall contractor is the main risk. The electrical first fix must be complete before the boards go on, and the boxes must be set to the correct line before the boards are fixed. If the boards go on first, the boxes have to be cut in, which is slower and gives a poorer finish. Agree the sequence with the drywall contractor at the start of the floor, not when the boards are being delivered.
On steel frames, the conduit route is often in the stud zone or above the ceiling, so the box entry should be planned to suit. Alrouf switch boxes have bottom and side knockouts in 1/2" and 3/4" sizes, which gives flexibility, but the entry should still be chosen to avoid sharp bends and to keep the conduit clear of the board line. On a steel frame, a box set too deep will not accept the accessory; a box set too proud will not accept the cover flush.
How Do You Set Boxes to the Finished Plaster Line Without Rework?
Setting boxes to the finished plaster line is a measuring and communication task, not a fixing task. The first step is to confirm the plaster or board build-up with the finishing subcontractor and record it on the setting-out drawing. The second is to use a setting gauge — a simple timber or metal gauge cut to the plaster depth — so that every box on the floor is set to the same line. The third is to check with a straight edge across the wall face before the mortar sets, not after.
On blockwork, the plaster depth can vary between internal and external walls and between specification sections. On precast, the panel face is the datum, but a screed or drylining zone may sit in front of it. On steel frame, the board thickness is the datum. In each case the box face must finish flush with the finished surface, and the only way to achieve that consistently is to measure the build-up and hold it.
A box set too deep can sometimes be recovered with a plaster ring or a box extension, but that adds a component and a cost. A box set too proud cannot be recovered without cutting back the plaster or the board, which is slow and visible. The cheaper strategy is to set slightly deep and use a plaster ring where needed, rather than to set proud and cut back. Agree that strategy with the finishing subcontractor before the first box is set.
Record the setting-out. A simple marked-up drawing showing box positions and plaster depth, signed by the electrical foreman and the finishing foreman, prevents the argument later. On a fast-moving Saudi project, the finishing subcontractor may change between floors; the drawing is the constant. Alrouf boxes are marked AL-ROUF KSA BS4662 (switch boxes BB6, BB7) or AL-ROUF KSA (junction boxes BB8, BB9, BB10), which makes them easy to identify at inspection, but the marking does not fix the box; the setting-out does.
What Fixing Details Control Pull-Out Strength and Cover Fit?
Pull-out strength comes from the substrate and the anchor, not from the box. In blockwork, the mortar bed and the block strength control it; in precast, the cast-in position or the anchor controls it; on steel frame, the stud and the bracket control it. The box itself is a galvanized steel pressing, and its job is to hold the accessory and the conduit entry, not to carry load. Fix the box so that the load path goes into the structure, not into the plaster or the board.
Cover fit depends on the box face being square to the wall and at the right depth. A box set out of level will show a gap at the cover; a box set too deep will not let the cover sit flush; a box set too proud will stand off the wall. Check level and plumb with a spirit level before the mortar sets, and check the cover fit on a sample box before setting out the floor. On switch boxes, the fixing centres are set by the box; on junction boxes, the cover is held by screws, so the box face must be flat and undamaged. For the full range of closure options, review this guide to electrical box covers and cover plates.
Conduit entry affects pull-out strength indirectly. A conduit bent sharply behind the box will strain the knockout and can crack the galvanized coating, which is the start of corrosion. Choose the knockout that matches the conduit route, remove only what is needed, and deburr the knockout if necessary. On Alrouf switch boxes, the bottom knockouts are 1/2" (3) and 3/4" (1), and the side knockouts are 1/2" (4) and 3/4" (6); on BB8, bottom 1/2"-3/4" (6) and 3/4"-1" (2), side 1/2"-3/4" (4) and 3/4"-1" (4); on BB9, bottom 1/2"-3/4" (2) and 3/4"-1" (1), side 1/2"-3/4" (8) and 3/4"-1" (4).
Fire rating is a property of the box and the wall assembly together. Alrouf boxes have a 2-hour fire rating, but the fixing must not compromise the wall's fire performance. On a fire-rated wall, use the fixing detail that the wall system requires, and do not cut or pack the wall in a way that breaches the rating. If in doubt, ask the wall system supplier, not the electrical supplier.
How Does Alrouf Support Fixing and Installation on Saudi Projects?
Alrouf manufactures its boxes in Dammam 2nd Industrial City from G90 galvanized steel as per ASTM-A653, with a 2-hour fire rating and country of origin Kingdom of Saudi Arabia. The range covers switch boxes BB6 and BB7 and junction boxes BB8, BB9 and BB10, with the sizes, thicknesses and knockout patterns listed above. The company also offers progressive die stamping, automated assembly, robotic welding, tooling and die design, tubular manufacturing, coil slitting and plastic injection molding, which means the box and its fixing interface are made under one roof. You can see the full manufacturing scope on the Alrouf services page.
For a Saudi project, that matters for two reasons. First, local content: a box made in the Kingdom supports Vision 2030 local content objectives and shortens the supply chain. Second, repeatability: a box made on a progressive die has consistent dimensions, knockout positions and marking, which makes setting out and fixing more predictable. A box that varies from batch to batch will vary on the wall, and the fixing detail has to absorb that variation.
The company does not offer free consultations, engineering reviews of drawings or CAD/CAM services, and does not state prices, delivery times or warranty terms. What it does offer is a manufactured product with known dimensions and markings, and a manufacturing capability that can be discussed with the procurement team. For fixing, the contractor's own setting-out and coordination with the finishing and precast subcontractors remain the controlling factors.
On an Eastern Province project, the practical support is the product data: sizes, thicknesses, weights, knockout patterns and markings. Use that data to plan the fixing detail before the first box is set. A switch box BB6-003 is 7×14×3.5 cm at 0.6 mm and 109 g, packed 50 pcs per pack; BB7-001 is 7×14×4.7 cm at 0.9 mm and 196 g, packed 50 pcs per pack; BB7-003 is 7×14×4.7 cm at 1.2 mm and 260 g, packed 50 pcs per pack. The thicker boxes are stiffer and hold their shape better in a chase, which can matter on a long run.
◈ Key Takeaways
- ✦Confirm the plaster or board build-up with the finishing subcontractor before setting the first box, and hold that depth with a setting gauge.
- ✦In blockwork, bed the box in mortar to the finished plaster line and brace it until set; in precast, cast the box in at the factory wherever possible; on steel frame, fix to the stud, not the board.
- ✦Choose the knockout that matches the conduit route and remove only what is needed, so the conduit does not strain the box or crack the galvanized coating.
- ✦Check level, plumb and cover fit on a sample box before setting out the floor, and record the setting-out on a marked-up drawing signed by the electrical and finishing foremen.
- ✦Use the Alrouf product data — sizes, thicknesses, knockout patterns and markings — to plan the fixing detail before the first box is set.
Frequently Asked Questions
❓ What is the best way to fix galvanized steel electrical boxes to blockwork in Saudi Arabia?
For blockwork, use mortar or plaster to embed the box securely, ensuring it is flush with the finished wall surface. Alternatively, use appropriate screws and plugs for a mechanical fix, but always follow local construction practices. Alrouf boxes are made of G90 galvanized steel as per ASTM-A653, providing corrosion resistance in Saudi Arabia's climate.
❓ How do I install galvanized steel electrical boxes in precast concrete walls?
In precast concrete, boxes are typically cast into the panels during production or fixed using specialized anchors and adhesives after casting. Ensure the box is properly aligned and secured to prevent movement during concrete pouring. Alrouf switch boxes are marked AL-ROUF KSA BS4662, ensuring compliance with quality standards.
❓ Why should I choose galvanized steel boxes over plastic for electrical installations in Saudi Arabia?
Galvanized steel boxes offer superior durability, fire resistance, and protection against impact and corrosion, which is crucial in Saudi Arabia's harsh environment. Alrouf boxes have a 2-hour fire rating, enhancing safety in residential and commercial buildings.
❓ Can I use Alrouf junction boxes for outdoor applications in Saudi Arabia?
Alrouf junction boxes are made of G90 galvanized steel as per ASTM-A653, providing good corrosion resistance, but for outdoor use, additional protection such as proper sealing and mounting in sheltered areas is recommended. Always ensure knockouts are sealed to prevent moisture ingress.
❓ How long does it take to install a galvanized steel electrical box in blockwork?
Installation time varies based on wall conditions and method, but typically each box can be fixed within 15-30 minutes using mortar or mechanical fixings. Proper planning and using quality products like Alrouf boxes can streamline the process.
See the full Alrouf product range
Download the Alrouf 2023 catalogue and browse the product range.
Alrouf Electrical Accessories Manufacturer
Galvanized electrical boxes & precision metal-plastic components — Dammam








